ECRA/ESA licensed · Barrie & Simcoe County
Electricians in Barrie who pull the permit
Panel upgrades, ESA inspections, aluminum wiring remediation and emergency callout — across Barrie, Innisfil, Oro-Medonte and Springwater. Every job notified to the Electrical Safety Authority, every price quoted before we start.
- Same-day callback before 4pm
- ESA permit included in the quote, not extra
- A straight answer on whether it can wait
Circuit directory
Start with what's actually happening
Most people call us describing a symptom, not a service. Find yours below — it maps to the work that usually fixes it, and roughly what it runs in Barrie.
- No power to half the house Emergency callout Call now
- Burning smell near an outlet Emergency callout Call now
- Breakers keep tripping Panel upgrade Don't wait
- Lights dim when the furnace kicks on Service upgrade Don't wait
- Aluminum wiring flagged by an insurer Pigtailing or rewire Don't wait
- Knob-and-tube found in the attic Rewire Don't wait
- Buying a house, need an ESA inspection ESA inspection Book ahead
- Adding a hot tub, EV charger, or subpanel New circuit Book ahead
- Power keeps going out in winter storms Transfer switch Book ahead
- Want pot lights in the kitchen Lighting install Book ahead
Not on the list? Describe it over the phone — we can usually tell you whether it needs a truck today or can wait for a scheduled visit. (249) 800-0317
What we do
Every job, with the permit and the price up front
Fixed quotes on planned work, hourly on diagnosis. Prices below are what these jobs actually run in Barrie in 2026 — not a national average with a local page wrapped around it.
-
Panel upgrades
Moving from 60 or 100 amp to a modern 200 amp service, including the ESA permit and the Alectra service connection.
$2,250–$4,500 Typical 100A → 200A upgrade, mast and meter base included -
Emergency callout
Burning smells, dead circuits, sparking outlets, storm damage. Live phone, not an answering service.
$90–$150 / hr After-hours callout, diagnosis included -
ESA inspections
Pre-purchase electrical inspections, insurance-required certificates, and clearing outstanding ESA deficiencies.
Flat-quoted visit Full residential inspection with written report -
Aluminum wiring
AlumiConn pigtailing and full remediation for the 1966–1978 Barrie builds insurers keep flagging.
$2,000–$4,500 Whole-home pigtailing, typical 3-bedroom -
Knob & tube
Staged rewiring for pre-1950 downtown and Allandale homes, with insurance certificates at each stage.
$8,000–$20,000+ Partial to full rewire, varies with access -
EV chargers
Level 2 charger installs with a real load calculation, permitted through ESA, plus load management where the service is tight.
$800–$1,500 + charger Level 2, typical attached garage run -
Lighting
Retrofit LED pot lights, fixture replacement, and switching — cut in cleanly with insulation-contact-rated housings.
Quoted per opening Per pot light, retrofit into existing ceiling -
Backup power
Manual and automatic transfer switches, standby generator hookups, and interlock kits — safely, and legally.
Quoted by configuration Interlock kit through to automatic transfer switch
Barrie housing stock
Your street predicts your panel
Barrie built out in distinct waves, and each one left a different electrical problem behind. We can usually guess what we will find before we open the panel.
| Era | Where | What we find | Typical service |
|---|---|---|---|
| 1900–1940 | Downtown, Allandale | Knob-and-tube remnants behind later renovations | 60 amp service |
| 1950–1965 | Letitia Heights, Codrington | Undersized panels, no grounding at outlets | 60–100 amp |
| 1966–1978 | Sunnidale, Grove East | Aluminum branch wiring — insurers flag it | 100 amp |
| 1985–2000 | Painswick, Holly | Federal Pioneer and Zinsco panels reaching end of life | 100–200 amp |
| 2000–2015 | Ardagh Bluffs, Innis-Shore | Fine, until an EV charger or hot tub gets added | 200 amp |
Where we work
Barrie and the townships around it
Seven service areas, and they are genuinely different jobs. Innisfil is on InnPower, Oro-Medonte and Springwater are on Hydro One, Barrie is on Alectra — which decides who we book a service disconnect with, and how far ahead.
FAQ
Questions we get asked
How much does an electrician cost in Barrie?
Published Ontario rates for a licensed electrician run $90 to $150 per hour on weekdays, with a one-hour minimum that includes diagnosis and a premium for after-hours and weekend callouts. Larger jobs — panel upgrades, rewires, EV chargers — are quoted as a fixed price for the whole job rather than by the hour, so the rate question mostly matters for small repair calls.
Do you pull ESA permits?
On every job that requires one, and the cost is inside the quote. A permit means the Electrical Safety Authority inspects the work and issues a Certificate of Acceptance, which is the document your insurer or a future buyer's lawyer will ask for. Work done without one is invisible until it costs you at a closing.
What areas do you cover?
Barrie, Innisfil, Stroud, Oro-Medonte, Springwater, Midhurst, Angus and Alliston. Barrie and the immediately surrounding communities are triaged first; Alliston is at the edge of our range and is scheduled around the route for non-urgent work.
How quickly can you come out for an emergency?
That depends on the day and where the truck is, so we give you an honest window on the phone rather than saying we are on our way and leaving you waiting. Anything burning, arcing, or a breaker that will not stay reset goes to the front of the queue.
My insurance company is asking about my panel. What do I do?
Send us the letter. Nine times out of ten it is a Federal Pioneer Stab-Lok panel, aluminum branch wiring, or a 60 amp service, and each has a defined fix with a defined cost. We correct it under permit, and the ESA Certificate of Acceptance is the document that closes the file with your broker.
Are you licensed and insured?
Every crew we send works under a contractor licensed with the Electrical Safety Authority, and insurance and WSIB clearance are shown before work starts. Ask for the ECRA/ESA licence number and check it yourself on the ESA public register before you book anyone, including us. Any contractor who will not give you that number is telling you something.
Talk to a Barrie electrician
Describe what the panel is doing over the phone. We can usually tell you whether it needs a truck today or can wait for a scheduled visit — and roughly what it costs — before anyone books anything.